Design Analysis of OSPF (Open Shortest Path First) Routing by Calculating Packet Loss Of Network WAN (Wide Area Network)

T.M Diansyah, Divi Handoko, Ilham Faisal, Annisa Yunianti, Kalvin Chiuloto, Risko Liza
2019 Journal of Physics, Conference Series  
In companies both large and small, they must always communicate and exchange data to other divisions at a considerable distance. In carrying out the process of data exchange, it is not uncommon for the data to suffer damage and some do not even reach the destination, the incident is known as packet loss. Therefore, a routing protocol is needed to solve the problem. OSPF routing is the right routing to be implemented. Because, OSPF routing uses Dijkstra's algorithm to find the closest distance,
more » ... closest distance, OSPF determines the best path based on the lowest cost and OSPF also divides its network into several levels, so the information dissemination on each router becomes that has been done, messages time from PC to PC get a range of values of 0.25%. Based on the analysis table of packet loss, the packet is categorized very well, because the packet sent is not much lost. configuration Routing OSPF Of RouterA RouterA>enable RouterA>configure terminal RouterA(config)# router ospf 1 RouterA(config-router)#network 110.0.0.0 0.255.255.255 area 0 RouterA(config-router)#network 130.100.0.0 0.0.255.255 area 1 RouterA(config-router)# exit 2. Configuration Routing OSPF Of RouterB RouterB>enable RouterB>configure terminal RouterB(config)# router ospf 1 RouterB(config-router)# network 110.0.0.0 0.255.255.255 area 0 RouterB(config-router)# network 193.200.50.0 0.0.0.255 area 0 RouterB(config-router)# network 150.100.0.0 0.0.255.255 area 2 RouterB(config-router)# network 192.168.56.0 0.0.0.255 area 0 RouterB(config-router)# exit 3. Configuration Routing OSPF Of RouterC RouterC>enable RouterC>configure terminal RouterC(config)# router ospf 1 RouterC(config-router)#network 193.200.50.0 0.0.0.255 area 0 RouterC(config-router)#network 178.100.0.0 0.0.255.255 area 1 RouterC(config-router)# exit 4. Configuration Routing OSPF Of RouterD RouterD>enable RouterD>configure terminal RouterD(config)# router ospf 1 RouterD(config-router)# network 130.100.0.0 0.0.255.255 area 1 RouterD(config-router)# network 193.200.20.0 0.0.0.255 area 1 RouterD(config-router)# network 80.0.0.0 0.255.255.255 area 1 RouterD(config-router)# network 50.0.0.0 0.255.255.255 area 2 RouterD(config-router)# exit 5. Configuration Routing OSPF Of RouterE RouterE>enable RouterE>configure terminal RouterE(config)# router ospf 1 RouterE(config-router)# network 50.0.0.0 0.255.255.255 area 2 RouterE(config-router)# network 150.100.0.0 0.0.255.255 area 2 RouterE(config-router)# network 90.0.0.0 0.255.255.255 area 2 RouterE(config-router)# network 200.200.20.0 0.0.0.255 area 2 RouterE(config-router)# exit 6. Configuration Routing OSPF Of RouterF RouterF>enable RouterF>configure terminal RouterF(config)# router ospf 1 RouterF(config-router)# network 178.100.0.0 0.0.255.255 area 1 RouterF(config-router)# network 205.205.100.0 0.0.0.255 area 1 RouterF(config-router)# network 90.0.0.0 0.255.255.255 area 2 RouterF(config-router)# network 60.0.0.0 0.255.255.255 area 1 RouterF(config-router)# exit Configuration Routing OSPF Of Multiuser2 The following each configuration IP address router of multiuser2. Configuration Routing OSPF Of RouterA RouterA>enable RouterA>configure terminal RouterA(config)# router ospf 1 RouterA(config-router)# network 59.0.0.0 0.255.255.255 area 1 RouterA(config-router)# network 168.168.0.0 0.0.255.255 area 1 RouterA(config-router)# exit 2. Configuration Routing OSPF Of RouterB RouterB>enable RouterB>configure terminal RouterB(config)# router ospf 1 RouterB(config-router)# network 59.0.0.0 0.255.255.255 area 1 RouterB(config-router)# network 210.198.100.0 0.0.0.255 area 0 RouterB(config-router)# network 192.168.56.0 0.0.0.255 area 0 RouterB(config-router)# network 41.0.0.0 0.255.255.255 area 2 RouterB(config-router)# network 194.150.150.0 0.0.0.255 area 0 RouterB(config-router)# exit 3. Configuration Routing OSPF Of RouterC RouterC>enable RouterC>configure terminal RouterC(config)# router ospf 1 RouterC(config-router)# network 41.0.0.0 0.255.255.255 area 2 RouterC(config-router)# network 190.198.0.0 0.0.255.255 area 2 RouterC(config-router)# exit 4. Configuration Routing OSPF Of RouterD RouterD>enable RouterD>configure terminal RouterD(config)# router ospf 1 RouterD(config-router)# network 25.0.0.0 0.255.255.255 area 0 RouterD(config-router)# network 168.168.0.0 0.0.255.255 area 1 RouterD(config-router)# network 99.0.0.0 0.255.255.255 area 0 RouterD(config-router)# network 210.198.100.0 0.255.255.255 area 0 RouterD(config-router)# exit 5. Configuration Routing OSPF Of RouterE RouterE>enable RouterE>configure terminal RouterE(config)# router ospf 1 RouterE(config-router)# network 33.0.0.0 0.255.255.255 area 0 RouterE(config-router)# network 190.198.0.0 0.0.255.255 area 2 RouterE(config-router)# network 99.0.0.0 0.255.255.255 area 0 RouterE(config-router)# network 194.150.150.0 0.0.0.255 area 0 RouterE(config-router)# exit
doi:10.1088/1742-6596/1361/1/012087 fatcat:ek252y5wm5e5vjmchizosmefwu